ورود
مقالات فارسیISIکنفرانسهاژورنالها

The Effect of Process Parameters and Tool Geometrical Parameters on the Tool Peak Temperature in Machining Process

محل انتشار: مجله بین المللی طراحی پیشرفته و تکنولوژی ساخت، دوره: 14، شماره: 3
سال انتشار: 1400
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 293

فایل این مقاله در 9 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:
https://civilica.com/doc/1296007

شناسه ملی سند علمی:

JR_ADMTL-14-3_009

تاریخ نمایه سازی: 1 آبان 1400

چکیده مقاله:

In the present study, the effects of process and geometrical parameters on the maximum temperature of tool have been investigated. Simulation of mild steel machining process in different cutting depths, speed of rotation (SOR), feeding rates, and different rake angles was performed. To verify the simulation, numerical results were compared with experimental results. Based on the results, it was found that by increasing the speed of rotation at a constant cutting depth and a constant feed rate, the maximum temperature of the process experiences a significant increase. By increasing the depth of the cut, the geometric location of the workpiece maximum temperature was transmitted to the edge of the tool and surface changes occurred, which it was accompanied with increment in the depth of the cut. The tool with the rake angle of -۱۰° and the depth of cutting of ۲ mm had the highest recorded temperature due to the lack of sufficient space for removing chips from the work surface.

کلیدواژه ها:

Geometrical parameters ، Machining ، Tool Shape ، Tool Temperature

نویسندگان

Maziar Mahdipour Jalilian

Department of Mechanical Engineering, Kermanshah Branch, Islamic Azad University, Kermanshah, Iran

Amir Ghiasvand

Department of Mechanical Engineering, University of Tabriz, Iran

Hasan Kheradmandan

Department of Mechanical Engineering, Kermanshah Branch, Islamic Azad University, Arak, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • Hashmi, K. H., Zakria, G., Raza, M. B., and Khalil, ...
  • D’addona, S. J. Raykar, and M. Narke, "High speed machining ...
  • Wang, B., Liu, Z., Evaluation on Fracture Locus of Serrated ...
  • Bordin, S., Sartori, S., Bruschi, and Ghiotti, A., Experimental Investigation ...
  • Umbrello, D., Caruso, S., and Imbrogno, S., Finite Element Modelling ...
  • Özel, T., Zeren, E., Finite Element Modeling the Influence of ...
  • Karpat, Y., Temperature Dependent Flow Softening of Titanium Alloy Ti۶Al۴V: ...
  • Ghiasvand, S. Hassanifard, Numerical Simulation of FSW and FSSW with ...
  • Cavaliere, P., De Santis, A., Panella, F., and Squillace, A., ...
  • Schmidt, H., Hattel, J., and Wert, J., An Analytical Model ...
  • Arrazola, P. J., Investigations on the Effects of Friction Modeling ...
  • Marimuthu, P. K., Prasada, T. H., and Kumar, C., ۳d ...
  • Jafarian, F., Ciaran, M. I., Umbrello, D., Arrazola, P., Filice, ...
  • Akhil M. H., Akhil C K, Afeez, C. K., Akhilesh, ...
  • Mousavi, S., Kelishami, A. R., Experimental and Numerical Analysis of ...
  • MatWeb, L., MatWeb: Material Property Data, línea]. Available: http://www.matweb. com/search/DataSheet. ...
  • Johnson, G. R., Cook, W. H., Fracture Characteristics of Three ...
  • Duan, C., Dou, T., Cai, Y., and Li, Y., Finite ...
  • Iqbal, M., Senthil, K., Bhargava, P., and Gupta, N., The ...
  • Hibbit, H., Karlsson, B., and Sorensen, E., ABAQUS User Manual, ...
    • نمایش کامل مراجع