Effects of Homogenization Conditions and Hot Rolling Parameters on Grain Refinement of an As-Cast ۳۰۱ Stainless Steel

سال انتشار: 1387
نوع سند: مقاله ژورنالی
زبان: انگلیسی
مشاهده: 49

فایل این مقاله در 8 صفحه با فرمت PDF قابل دریافت می باشد

استخراج به نرم افزارهای پژوهشی:

لینک ثابت به این مقاله:

شناسه ملی سند علمی:

JR_ISSIRAN-5-2_004

تاریخ نمایه سازی: 6 آبان 1402

چکیده مقاله:

In this work, effects of homogenization time of ۳ to ۱۳ h at ۱۲۰۰ °C on the grain refinement of as-cast AISI ۳۰۱ stainless steel after different hot rolling conditions were investigated. The results showed that the minimum grain size of ۱۶±۷ mm was achieved when homogenization took place at ۱۲۰۰ °C for ۹ h followed by hot rolling at temperature range of ۱۰۰۰–۱۲۰۰ °C with strain of ۰.۸ and strain rate of ۱.۲ s-۱ and annealing at ۱۰۵۰ °C for ۳ min. Effect of Nb element on the retardation of recrystallization was pronounced. It seems that there is an optimum solute segregation below which retardation and above which grain growth of recrystallized grains is dominant. It was also found that this optimum homogenization condition was dependent upon the hot rolling parameters; higher the strain and strain rate resulted in lower homogenizing time at ۱۲۰۰ °C.

نویسندگان

M. Eskandari

Department of Materials Engineering, Isfahan University of Technology, Isfahan ۸۴۱۵۶-۸۳۱۱۱, Iran

A. Najafizadeh

Department of Materials Engineering, Isfahan University of Technology, Isfahan ۸۴۱۵۶-۸۳۱۱۱, Iran

A. Kermanpur

Department of Materials Engineering, Isfahan University of Technology, Isfahan ۸۴۱۵۶-۸۳۱۱۱, Iran

M. Karimi

Department of Materials Engineering, Isfahan University of Technology, Isfahan ۸۴۱۵۶-۸۳۱۱۱, Iran

مراجع و منابع این مقاله:

لیست زیر مراجع و منابع استفاده شده در این مقاله را نمایش می دهد. این مراجع به صورت کاملا ماشینی و بر اساس هوش مصنوعی استخراج شده اند و لذا ممکن است دارای اشکالاتی باشند که به مرور زمان دقت استخراج این محتوا افزایش می یابد. مراجعی که مقالات مربوط به آنها در سیویلیکا نمایه شده و پیدا شده اند، به خود مقاله لینک شده اند :
  • H. J. McQueen, J. J. Jonas: Appl. Metalworking, ۳(۳) (۱۹۸۴), ...
  • I. Tamura, H. Sekine, T. Tanaka, C. Ouchi: Thermomechanical Processing ...
  • S. Yamamoto, C. Ouchi, T. Osuka: Thermomechanical processing of microalloyed ...
  • K. T. Aust, J. W. Rutter, Trans. MIME, ۲۱۵ (۱۹۵۹), ...
  • Y. Qingbo, Y. Sun, Mate. Sci.Eng.A, (۲۰۰۶), ۴۲۰ ...
  • L. M. Storozheva, Metal Sci. Heat Treat., ۳۱ (۹-۱۰) (۱۹۹۰), ...
  • M. Enomoto, H. I. Aaronson, Scripta Metall, ۱۹ (۱۹۸۵), ۱ ...
  • M. Enomoto, Y. Sato, Mater. Trans A, ۳۵ (۱۹۹۴), ۸۶۲ ...
  • A. I. Zaky Farahat, T. El-Bitar, Eman El-Shenawy: Mater. Sci. ...
  • A. Belyakov, H. Miura, T. Sakai, Mater. Sci.Eng.A, ۲۵۵ (۱۹۹۸), ...
  • W. Roberts, B. Ahlblom, Acta Metall., ۲۶ (۱۹۷۸), ۸۰۱ ...
  • E. Brunger, X. Wang, G. Gottstein, Scripta Mater., ۳۸ (۱۹۹۸), ...
  • W. F. Hosfor, R. M. Caddell, Metal Forming-Mechanics and Metallurgy, ...
  • نمایش کامل مراجع